Allen-Bradley 2-D Bedienungsanleitung Seite 135
- Seite / 172
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Troubleshooting and Fault Information
6-10
Table 6.C Troubleshooting (continued)
General Problem Action to Take
Motor not accelerating properly. (1) Check motor
- Verify that motor is connected properly.
- Verify that no mechanical problems exist.
2) Check control input signals
- Verify that SW1, SW2, and SW3 are in the proper state to select desired Accel/Decel rates.
(Refer to Table 5.A on page 5-29)
(4) Check parameter settings and charts on Pages 5-29 and 5-30.
- Verify that [Accel Time 1] and [Accel Time 2] are set properly.
- Verify that [Current Limit] is set properly.
- Verify that [DC Boost Select] is set correctly.
- Verify that [Start Boost] and [Run Boost] are set properly.
Specific Problem Action to Take
Can not Jog from Adapter. (1) Verify that [Jog Mask] is set properly to allow jogging from that adapter.
(2) Verify that [Logic Mask] is set properly to allow jogging from that adapter.
(3) Is drive already running?
(4) Examine [Stop Owner] to verify that a maintained Stop does not exist.
Can not change direction from Adapter. (1) Verify that [Direction Mask] is set to allow direction changes from that adapter.
(2) Verify that [Logic Mask] is set to allow direction changes from that adapter.
Can not Start from Adapter. (1) Verify that [Start Mask] is set properly to allow starting from that adapter.
(2) Verify that [Logic Mask] is set properly to allow starting from that adapter.
(3) Is drive already running?
(4) Examine [Stop Owner] to verify that a maintained Stop does not exist.
Display indicates “Not Enabled”. (1) Check enable signal at TB2, terminals 11 & 12.
- 1305 Adjustable 1
- Frequency AC Drive 1
- (Series C) 1
- PLEASE READ! 2
- IMPORTANT USER INFORMATION 2
- Summary of Changes 3
- SUMMARY OF DRIVE ENHANCEMENTS 4
- Table of Contents 7
- Appendix D – CE Conformity 8
- GENERAL PRECAUTIONS 10
- NAMEPLATE LOCATION 12
- 1305-BA03A-HAP SER C 12
- FIRMWARE COMPATIBILITY 12
- 1305 – A02 AA 13
- Information and Precautions 14
- Installation/Wiring 15
- TERMINAL BLOCK ACCESS 17
- INPUT DEVICES 19
- INPUT POWER CONDITIONING 20
- INPUT FUSING 20
- RFI FILTERING 22
- POWER WIRING 25
- P-P insulation design 27
- DRIVE OPERATION WITHOUT A 31
- HUMAN INTERFACE MODULE (HIM) 31
- CONTROL WIRING 31
- User Side 34
- OUTPUT DEVICES 36
- CABLE TERMINATION 36
- ADAPTERS 37
- HIM DESCRIPTION 39
- HIM OPERATION 39
- Human Interface Module 40
- OFF Steady ON 41
- Steady ON OFF 41
- Flashing Steady ON 41
- Steady ON Flashing 41
- HIM REMOVAL AND INSTALLATION 42
- HIM MODES 43
- OPERATOR LEVEL 44
- MODE LEVEL 44
- GROUP LEVEL 44
- PARAMETER LEVEL 44
- PROGRAM AND DISPLAY MODES 45
- Accel Time 46
- 99.9 Secs 46
- Choose Group 46
- Adapter 4 47
- X1111111 47
- PROCESS MODE 48
- Choose Mode 49
- Process Text 1 49
- EEPROM MODE 50
- EEPROM MODE (continued) 51
- CONTROL STATUS MODE 54
- PASSWORD MODE 56
- PASSWORD MODE (continued) 57
- Start-Up 60
- DESCRIPTION 61
- HIM DISPLAY 61
- Bul. 1305 Drive 62
- Connection Fail 62
- Open Enable Signal 65
- Restore Enable Signal 65
- Remove ALL Power 67
- Reconnect Motor 67
- Slowly Increase Speed 69
- PROGRAMMING EXAMPLE 73
- Metering Group (continued) 75
- 5-2 & 5-3 77
- Setup Group (continued) 78
- Figure 5.10 Start/Run Boost 88
- Figure 5.12 Analog Invert 90
- Two times 97
- [Skip Freq Band] 97
- Programming 100
- (continued) 100
- Figure 5.16 S-Curve 102
- Figure 5.17 S-Curve Time 103
- [( )])( )( 104
- Faults Group (continued) 109
- Diagnostics Group (continued) 112
- Masks Group (continued) 117
- Owners Group (continued) 120
- CHAPTER OBJECTIVES 126
- FAULT INFORMATION 126
- (continued) 129
- Appendix 138
- Table A.1 Specifications 139
- Serial Communications 144
- LOGIC CONTROL DATA 145
- DRIVE STATUS DATA 145
- SCALE FACTOR CONVERSION 145
- 25% of DRV 149
- 20% of DRC 149
- Drive Accessories 160
- ➀ Input reactor only 161
- CE Conformity 162
- ELECTRICAL CONFIGURATION 164
- GROUNDING 164
- CUT ALONG DOTTED LINE 170
Verwandte Produkte und Handbücher für Barcodeleser Allen-Bradley 2-D
Barcodeleser Allen-Bradley 2755 Bedienungsanleitung
(115 Seiten)
(115 Seiten)
Barcodeleser Allen-Bradley 2-D Bedienungsanleitung
(134 Seiten)
(134 Seiten)
Barcodeleser Allen-Bradley 2755 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern