Allen-Bradley 2-D Bedienungsanleitung Seite 44
- Seite / 92
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
5-6 Parameters and Programming
Program Group Parameters
This group contains parameters whose values can be programmed. Refer to
Programming Example earlier in this chapter. Unless otherwise stated, parameters
that are programmed while the drive is running take immediate effect.
Program Group
No. Parameter Name/Description
Min./Max.
Range
Units
Factory
Default
30 [Accel Time 1]
Time for the drive to ramp from 0.0 Hz. to P33 - [Maximum Frequency]. The rate
is linear for any increase in command frequency unless P53 - [S-Curve] is set to
a value other than “0”. Setting this to 0.0 sec. gives 0.1 sec acceleration with the
initial current limit turned off. This allows quicker acceleration times for low inertia
systems. For medium to high inertia systems, the minimum value should be 0.1
sec.
0.0/600.0 0.1
Seconds
10.0
Seconds
31 [Decel Time 1]
Time for the drive to ramp from P33 - [Maximum Frequency] to 0.0 Hz. The rate
is linear for any decrease in command frequency unless P53 - [S-Curve] is set to
a value other than “0”. See P30 - [Accel Time 1] figure above.
0.1/600.0 0.1
Seconds
10.0
Seconds
32
➊
[Minimum Frequency]
Lowest frequency that drive will output continuously.
0/240 1 Hz 0 Hz
33
➊
[Maximum Frequency]
Highest frequency the drive will output.
This parameter cannot be changed while running. The value of this parameter
setting must be greater than the value set in P32 - [Minimum Frequency].
0/240 1 Hz 60 Hz
34 [Stop Mode Select]
Determines stopping mode used by the drive when a stop is initiated. Refer to
the P44 - [DC Hold Time] and P45 - [DC Hold Voltage] diagrams.
Settings:
0 Ramp to Stop
1 Coast to Stop
2 DC Injection Braking
3 DC Injection Braking (w/Auto Shutoff) – works the same as standard DC injection
braking except that it may shut off before the P44 - [DC Hold Time]. This occurs
if the drive is out of current limit before the P44 - [DC Hold Time] expires.
0/3 Numeric
Value
0
35 [Base Frequency]
Set value to rated nameplate frequency of motor. A Program Keypad Module is
required if P35 must be changed to 50 Hz.
10/240 1 Hz 60 Hz
➊
The analog inputs to the drive (i.e. 4-20mA, 0 to +10 V, or remote potentiometer) can be scaled to P32 - [Minimum Frequency] and
P33 - [Maximum Frequency] by programming P75 - [Analog Input Minimum] and P76 - [Analog Input Maximum].
Speed
0
Time
Maximum
Frequency
Accel Time Decel Time
0
Acceleration
Deceleration
- 160 SSC™ 1
- Variable Speed 1
- (Series C) 1
- Important User Information 2
- Series C Summary of Changes 3
- Table of Contents 5
- Getting Started 7
- 160 -AA02 N SF1 P1 8
- 160-AA02NSF1P1 9
- Standard Drive Features 10
- Optional Drive Features 11
- End of Chapter 12
- Installation and Wiring 13
- Power Wiring 14
- Specifications 15
- Terminal Block Wiring 15
- Motor Branch Circuit Analysis 16
- Input Power Conditioning 18
- Motor Cable Types 18
- Reflected Wave Protection 19
- Capacitive Current Coupling 20
- Nm (lb in) 21
- Wiring Diagram Key 22
- 2-12 Installation and Wiring 24
- Installation and Wiring 2-17 29
- Analog Frequency Sources 30
- Preset Frequency Sources 31
- Internal Frequency Source 32
- Program Keypad Module 33
- Key Functions 34
- Program Keypad Module 3-3 35
- Installation 36
- Start-Up 37
- 4-2 Start-Up 38
- Parameters and Programming 39
- Important Reset Actions 40
- Programming Example 40
- Display Group (Read Only) 43
- 0/48 Numeric Value 43
- Program Group Parameters 44
- % [Base Frequency] 45
- % [Base Voltage] 45
- 46 [Input Mode] 47
- 47 [Output Configure] 47
- 48 [Output Threshold] 47
- 49 [PWM Frequency] 48
- 50 [Restart Tries] 48
- 51 [Restart Time] 48
- 52 [DB Enable] 48
- 53 [S-Curve] 49
- 54 [Clear Fault] 49
- 55 [Memory Probe Address] 49
- 56 [Reset Functions] 49
- Preset Speed Model Only 50
- Signal Follower 50
- Model Only 50
- Settings: 52
- 81 [PI Proportional Gain] 53
- 82 [PI Integral Gain] 53
- 83 [PI Process Reference] 53
- 84 [PI Dead Band] 53
- 160 PI Control Setup 54
- Troubleshooting 57
- Problem Corrective Action 59
- 6-4 Troubleshooting 60
- CSA 22.2 62
- Specifications A-3 63
- End of Appendix 64
- Accessories and Dimensions 65
- Accessory Dimensions 66
- Line Filters Figure B.3 67
- MADE IN U.S.A 68
- 29 ➊ 69
- Drive Dimensions 70
- 5.5 (0.22) 72
- Mounting Holes—2 Places 72
- CE Conformity 75
- Shielded Enclosure 76
- Cable Clamps 77
- Motor Cable 77
- Control Wiring TB3 78
- Ground Terminal – PE 78
- CE Conformity C-5 79
- Index-10 90
Verwandte Produkte und Handbücher für Barcodeleser Allen-Bradley 2-D
(96 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.147 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern